$92.36 $115.44
National Paint Waterbase Epoxy Tie-Kote is a two component water based epoxy tie-coat/sealer with excellent adhesive properties existing one and two part finishes. Primarily used on cleaned existing finishes which will be over coated with a two component solvent based finish which may attack the existing finish and cause a loss of adhesion. Can be used over chlorinated polymer pool paints, conventional solvent based and water based finishes such as alkyds, vinyls, acrylics and latex. Ideally applied by roller or brush but can be sprayed if desired.
Colors: Clear Amber
Finish: Matte
Vehicle Type: Amine Adduct Resin in Water
Solids By Volume: 47.0 +/- 1.0%
VOC Content: 0 grams/liter (reacted)
Weight per Gallon: 8.6 +/- 0.2 pounds
Recommended Dry Film Thickness: 2.0-2.5 mils
Coverage: Approximately 303 square feet per gallon at 2.5 mils DFT
Pot Life: 2-3 Hours
Shelf Life: 24 Months
Average Dry Time: Dries to touch in about 1 hour at 70-75 deg F. Can be top coated with solvent based epoxy finishes after an overnight cure.
Recommended Reducer: None recommended. Use tap water if necessary
Clean Up: Use tap water
Surface Preparation: Surface must always be clean, dry and properly prepared prior to painting. Failure to do so will lead to eventually blistering and/or peeling. High pressure fresh water clean if possible or solvent clean to remove all surface contaminants. Allow to thoroughly dry prior to over coating.
General Application: For use as a tie-coat/sealer over existing finishes that are desired to now be painted with solvent based epoxies. Apply by roller or brush. Add up to 10-15% by volume of tap water but only if necessary. Apply one or two coats if needed to meet dry film thickness requirements. Allow 15-20 minutes induction time after the curing agent component is added.
Mixing and Thinning: Shake or mix each component thoroughly. Add the curing agent component to the base component and stir thoroughly. Continue to stir while using.
Existing Painted Surfaces: First ensure the existing surface is compatible with a two component water based
PRODUCT DOWNLOADS:
$174.46 $218.24
Aquapoxy Primer is a two-component catalyst-cured epoxy primer that is safe and easy to use. The Aquapoxy finish coating is self-priming so Aquapoxy Primer is typically used to achieve a sound base coat, higher build with increased long term durability in mind. It shares the same surface tolerant breathable resins as the Aquapoxy finish coating with zero VOC and low odor. Adhesion, chemical resistance, hardness and long term durability are all excellent. Grinding or blasting not typically required on concrete with the use of TS-695 Etching Cleaner or Muriatic acid. Covers up to 200-250 square feet per gallon.
INTENDED USE: A two-component polyamine epoxy floor primer coating acceptable for heavy-duty commercial, industrial, and consumer use.
SURFACES: Concrete, tile, masonry and plaster.
USES: Manufacturing, industrial, commercial, retail, hospitals, food service, laundry rooms, hangars, basements and garage floor paint.
APPLICATION: Roll or spray.
NOT RECOMMENDED: For wooden surfaces.
$106.57 $133.21
Etching Primer is a phenolic modified alkyd primer coating that produces a sound base coat for all floor paint and coating products. An exceptionally high quality product that conforms to government specification number TT-P-664 C, D. Fast drying; it is dry enough to be over-coated in just two hours! Choose it for its speed, ease of application, tenacious (acid etching) bond and long term durability if provides. Adheres to virtually any surface. Guaranteed to be lacquer proof (won’t lift due to compatibility issues). One gallon covers up to 300 square feet. See Product Data Sheet for further details.
NOTE: This primer is porous, intended to draw the top coat into it creating an unbreakable bond. Care should be taken to be sure it does not draw in unwanted moisture at time of application.
INTENDED USE: A high adhesion primer coating for floor coating products. Intended for use on hard to adhere to surfaces. Industrial commercial and residential use.
SURFACES: Concrete, glazed tile, VCT tile, linoleum, masonry, metal, synthetic materials and wood.
USES: Hard to adhere to surfaces. Commercial and industrial areas, kitchens, food service areas, bathrooms and laundry rooms.
THINNER: TS-605 Thinner.
APPLICATION: Most applications are by roller coat but it is sprayable.
$64.96 $81.20
Mono-Epoxy Primer makes priming with epoxy easier than ever with its unique no-mix formula. A new generation epoxy-ester primer that utilizes oxygen curing rather than two-component catalyst-curing making it easier to use. Its exceptionally high level of performance and ease of application combine to make it a compelling choice. Provides a sound base for the application of most any floor paint or coating product. Grinding or blasting not typically required on concrete with the use of TS-695 Etching Cleaner or Muriatic acid. Covers up to 300 square feet per gallon. See Product Data Sheet for further details.
INTENDED USE: An easy to use no-mix epoxy floor coating primer acceptable for a wide variety of applications.
SURFACES: Concrete, tile, masonry and wood.
USES: Commercial kitchens, manufacturing and industrial areas, retail spaces, food service areas, bathrooms and laundry rooms. Excellent for use with epoxy garage floor coatings.
THINNER: TS-101 Thinner.
APPLICATION: Most applications are by roller coat but it is sprayable.
$173.20 $216.50
Ever-Last Epoxy Primer is a two component polyamide epoxy floor coating primer intended for heavy-duty applications. It is your best choice for use on concrete floors because it will not react negatively with alkalis within the concrete matrix. Use it wherever there is high volume motorized traffic or where corrosive chemicals, spilled fuel, oil or standing water is regularly present. Offers excellent adhesion and hardness with superior chemical resistance. Will not pick up to hot tires. Grinding or blasting not typically required on concrete with the use of TS-695 Etching Cleaner or Muriatic acid. Covers up to 300 square feet per gallon.
INTENDED USE: A super-duty epoxy floor primer coating intended for industrial floor coatings applications. Suitable for commercial and residential use.
SURFACES: Concrete, tile, masonry, fiberglass, metal and wood.
USES: Concrete floors, walkways, ramps, commercial kitchens, manufacturing areas, industrial areas, food service areas, bathrooms and laundry rooms. Acceptable for use with all epoxy garage floor coating products.
THINNER: TS-605 Thinner.
APPLICATION: Apply by roller-coat or spray.