- Questions (0)
A PREMIUM two-part solvent based epoxy coating designed for maximum protection, ease of application, outstanding gloss and color retention, chemical resistance and adhesion over a variety of substrates. Longest lasting protection against fade. Apply over most types of epoxy coatings in good condition, as well as bare concrete and steel. Dries quickly, durable, and resists fading, chemicals and abrasion. Mix ratio is 1:1.
SUGGESTED USES: Interior, concrete floors, steel, equipment, and anywhere a rugged industrial coating is needed
LIMITATIONS: Not recommended for applications requiring extended exterior exposure. Do not apply if material, substrate or ambient temperature is below 50°F or above 95°F.
COLORS: Available in over 100 factory packaged colors
VEHICLE TYPE: Epoxy Resin & Polyamide Curing Agents
SOLVENT TYPE: Xylene, Diacetone Alcohol, Butyl Cellosolve
VOC: 3.5 lbs. / gal (420 grams / liter)
SOLIDS BY WEIGHT: 58%
WEIGHT PER GALLON: 10 lbs. per gallon (varies by color)
RECOMMENDED DRY FILM: 4.0 mils
COVERAGE: Theoretical coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough or sandblasted surfaces.
VISCOSITY AT 75°F (24°C): 70-80 KU
AVERAGE DRY TIME 75°F: Dries to touch in 2 hours. Lower temperatures & higher humidity will slow down dry times. Recoat with no sanding required between 16 hours and 72 hours.
RECOMMENDED REDUCER: Xylene for spray application, High Flash Naphtha for brushing or rolling
RESISTANCE TO: Chemical Resistance, Abrasion, Oils, Grease
RECOMMENDED PRIMERS: Procote™ U/E 824N 2-Part Epoxy Gray Primer
APPLICATION: Brush, Spray or Roller Roll: 3/8” nap mohair metal, lambskin, phenolic core roller. Keep roller wet. Roll in one direction, rewet, then cross roll. Product can be reduced as needed with High Flash Naphtha to allow proper flow out and performance. Spray: Conventional Air Gravity Feed 59–70 psi, Tip Size .055 –.070, Airless 2200-2500 psi, Tip Size .013-.017. Product can be reduced with Xylene as needed for proper flow out and performance. For Air Spray reduce 25% with urethane reducer (Xylene.).
SURFACE PREPARATION: Water blast surface to remove all loose paint, dirt, oils and grease. Abrade with 240 grit dry sandpaper or equivalent. Solvent wipe down to remove all sanding residue. Prime with Epoxy Kote™ U/E 824N 2-Part Epoxy Gray Primer for best results.
POT LIFE: 6 hours at 75°F, 50% Humidity.
SHELF LIFE: Minimum 12 months
MIXING: Mechanically mix for 10 minutes both Part A & Part B individually, and then mechanically mix 10 minutes the combined volumes (1:1 Mix Ratio). Allow mixed solution to induct for 30 minutes before using. Mix only what you expect to use in an 6 hour period.
PACKAGE: 1 Gallon cans, 5 gallon pails.
CLEANUP: Xylene for Equipment.
Aquapoxy is a new generation catalyst-cured epoxy floor finish that produces excellent results without harming you or the environment. And it’s tough! Recently chosen by 7-11 Stores (world’s largest retail chain) for use in all new construction. Utilizes breathable resin technology to produce an exceptionally hard, durable, surface tolerant finish. Adhesion, chemical resistance, hardness and long term durability are all impressive! This unique combination of environmental and performance properties make it a favorite with architects and property managers. Acceptable for use where heavy traffic, corrosive chemicals, impacts and abrasions are present. Grinding or blasting not typically required with the use of TS-695 Etching Cleaner or Muriatic acid. Covers 200-250 square feet per gallon. Apply one or two coats as desired. Two coats recommended in H-D and commercial applications.
INTENDED USE: A super-duty concrete coating for floors. Primarily for interior use but may be used outdoors.
SURFACES: Concrete, tile, VCT, masonry, plaster, fiberglass, synthetic materials.
USES: Commercial industrial use, hangars, commercial kitchens, retail, bathrooms, parking garages, concrete sealer and garage floor coatings. Approved for food service.
PRIMER: None required on concrete and tile. Glazed tile, linoleum & fiberglass use TS-664.
APPLICATION: Roll or spray.
NOT RECOMMENDED: For wooden surfaces.
Aquapoxy II Clear produces a durable epoxy finish without the hassle of mixing two components. Like original Aquapoxy (TS-905) it is low VOC, nontoxic and environmentally friendly - but now easier to use! Adhesion, chemical resistance, hardness, long term durability and are ease of use are all excellent. It is acceptable for use where there is motorized traffic, chemicals, salt, high impacts and abrasions. It will not lift to hot tires. It utilizes breathable resin technology to produce a surface tolerant finish. Grinding or blasting not typically required with the use of TS-695 Etching Cleaner or Muriatic acid. It is self-priming and may be applied over any existing coating. Covers up to 250-300 square feet per gallon. Two coats required. Finish is high gloss.
INTENDED USE: Commercial grade finish coating for concrete and tile floors. Interior / exterior use.
SURFACES: Concrete, masonry, plaster, stucco, porous tile & VCT.
USES: Warehouses, driveways, restaurants, hospitals, laundry rooms, hangars, retail spaces and basements. Approved for food service.
PRIMER: Self-priming in two or more coats.
APPLICATION: Brush, roll or spray.
NOT RECOMMENDED: Commercial or residential floor application with vehicle traffic. Use Aquapoxy TS-905 2-part water-base epoxy.
Supreme Urethane is our most durable product. A super-duty two-component aliphatic acrylic polyurethane finish coating durable enough for the harshest environment and high abuse areas. This recent reformulation of TS-2 Hard-Shell Urethane offers lower VOC, twice the solid content resulting in higher build and increased long-term durability. Offers unequalled performance in a wide variety of categories including adhesion, hardness, chemical resistance, resistance to high heat, flexibity, color and gloss retention. Intended for use where heavy traffic, strong chemicals, high heat, spilled fuel, acids, alkalis, solvents, saltwater, high impacts and corrosion are present. Will not pick up to hot tires. Grinding or blasting not typically required with the use of TS-695 Etching Cleaner or Muriatic acid. Covers up to 300 square feet per gallon.
INTENDED USE: A super-duty finish coating for industrial, manufacturing and residential interior / exterior applications.
SURFACES: Concrete, tile, masonry, plaster, wood, fiberglass, synthetic materials and all metals.
USES: Commercial use, hangars, bathrooms, commercial kitchens, parking garages, drive through areas, concrete sealer and garage floor paint. Approved for food service.
PRIMER: Concrete TS-6390, glazed tile linoleum & fiberglass TS-664, wood, none required.
THINNER: TS-605 Thinner.
APPLICATION: Brush, roll or spray.
Mono-Epoxy rewrites the book on epoxy itself. A new generation alkyd epoxy-ester resin blend that eliminates the need for mixing multiple components making it easier to use. It can be used in hot and cold climates (-40F – 350F). Has a 10 year guaranty in swimming pools, which is a testimony to its durability. Its exceptionally high level of performance and ease of application combine to make it a compelling choice. Self-priming on porous materials, use recommended primer on non-porous materials. Grinding or blasting not typically required with the use of TS-695 Etching Cleaner or Muriatic acid. Covers up to 300 square feet per gallon. A minimum of two coats is required.
INTENDED USE: Commercial, industrial, manufacturing and residential interior / exterior. Epoxy floor paint.
SURFACES: Concrete, tile, masonry, fiberglass and metal.
USES: Commercial use, garage floors, basements, retail spaces, kitchens, laundry rooms, patios, porches, docks, ramps, walkways. Meets most concrete floor coatings requirements.
THINNER: TS-101 Leveling Thinner.
APPLICATION: Brush, roll or spray.