Aquapoxy Primer is a two-component catalyst-cured epoxy primer that is safe and easy to use. The Aquapoxy finish coating is self-priming so Aquapoxy Primer is typically used to achieve a sound base coat, higher build with increased long term durability in mind. It shares the same surface tolerant breathable resins as the Aquapoxy finish coating with zero VOC and low odor. Adhesion, chemical resistance, hardness and long term durability are all excellent. Grinding or blasting not typically required on concrete with the use of TS-695 Etching Cleaner or Muriatic acid. Covers up to 200-250 square feet per gallon.
INTENDED USE: A two-component polyamine epoxy floor primer coating acceptable for heavy-duty commercial, industrial, and consumer use.
SURFACES: Concrete, tile, masonry and plaster.
USES: Manufacturing, industrial, commercial, retail, hospitals, food service, laundry rooms, hangars, basements and garage floor paint.
APPLICATION: Roll or spray.
NOT RECOMMENDED: For wooden surfaces.
Etching Primer is a phenolic modified alkyd primer coating that produces a sound base coat for all floor paint and coating products. An exceptionally high quality product that conforms to government specification number TT-P-664 C, D. Fast drying; it is dry enough to be over-coated in just two hours! Choose it for its speed, ease of application, tenacious (acid etching) bond and long term durability if provides. Adheres to virtually any surface. Guaranteed to be lacquer proof (won’t lift due to compatibility issues). One gallon covers up to 300 square feet. See Product Data Sheet for further details.
NOTE: This primer is porous, intended to draw the top coat into it creating an unbreakable bond. Care should be taken to be sure it does not draw in unwanted moisture at time of application.
INTENDED USE: A high adhesion primer coating for floor coating products. Intended for use on hard to adhere to surfaces. Industrial commercial and residential use.
SURFACES: Concrete, glazed tile, VCT tile, linoleum, masonry, metal, synthetic materials and wood.
USES: Hard to adhere to surfaces. Commercial and industrial areas, kitchens, food service areas, bathrooms and laundry rooms.
THINNER: TS-605 Thinner.
APPLICATION: Most applications are by roller coat but it is sprayable.
Mono-Epoxy Primer makes priming with epoxy easier than ever with its unique no-mix formula. A new generation epoxy-ester primer that utilizes oxygen curing rather than two-component catalyst-curing making it easier to use. Its exceptionally high level of performance and ease of application combine to make it a compelling choice. Provides a sound base for the application of most any floor paint or coating product. Grinding or blasting not typically required on concrete with the use of TS-695 Etching Cleaner or Muriatic acid. Covers up to 300 square feet per gallon. See Product Data Sheet for further details.
INTENDED USE: An easy to use no-mix epoxy floor coating primer acceptable for a wide variety of applications.
SURFACES: Concrete, tile, masonry and wood.
USES: Commercial kitchens, manufacturing and industrial areas, retail spaces, food service areas, bathrooms and laundry rooms. Excellent for use with epoxy garage floor coatings.
THINNER: TS-101 Thinner.
APPLICATION: Most applications are by roller coat but it is sprayable.
Ever-Last Epoxy Primer is a two component polyamide epoxy floor coating primer intended for heavy-duty applications. It is your best choice for use on concrete floors because it will not react negatively with alkalis within the concrete matrix. Use it wherever there is high volume motorized traffic or where corrosive chemicals, spilled fuel, oil or standing water is regularly present. Offers excellent adhesion and hardness with superior chemical resistance. Will not pick up to hot tires. Grinding or blasting not typically required on concrete with the use of TS-695 Etching Cleaner or Muriatic acid. Covers up to 300 square feet per gallon.
INTENDED USE: A super-duty epoxy floor primer coating intended for industrial floor coatings applications. Suitable for commercial and residential use.
SURFACES: Concrete, tile, masonry, fiberglass, metal and wood.
USES: Concrete floors, walkways, ramps, commercial kitchens, manufacturing areas, industrial areas, food service areas, bathrooms and laundry rooms. Acceptable for use with all epoxy garage floor coating products.
THINNER: TS-605 Thinner.
APPLICATION: Apply by roller-coat or spray.
Seal-It! (Deep Penetrating Sealer) is a problem solver. It treats concrete and masonry three ways; it permanently seals out water, densifies and hardens it all at once. It contains a catalyst that seeks out and reacts with moisture, free alkali (lime), calcium hydroxides and other particles fusing them together creating an impenetrable silica. The entire matrix is converted into a solid mass creating a permanent barrier. Increases the bonding power floor coating products by up to 300%. Withstands up to 60 PSI hydro-static pressure! A true penetrating sealer not intended to be used over sealed surfaces or paint. Not a coating that leaves a finish! See concrete floor paints and coating products for finishes. One gallon treats 200 square feet. Three applications typically required. We strongly recommend making the VaproGuage Moisture Test part of your order. Call us or refer to product Data Sheet for further details.
INTENDED USE: A deep penetrating sealer that densifies and seals concrete permanently.
SURFACES: Concrete, porous tile and masonry.
USES: Concrete floors, walls, countertops, basements, food service areas and bathrooms. Use with any concrete floor paints.
APPLICATION: Most applications are by hand pump sprayer.
A PREMIUM one-part industrial enamel that are designed for all applications of steel, wood and masonry. Formulated especially as a heavy duty protective and decorative coating to withstand severe exposures. An epoxy resin, rust inhibitive paint for new or previously painted structural steel, rolled steel, aluminum all types of wood and masonry surfaces. Special processed chemical ingredients protect metal and wood against rust, rotting, corrosion, mildew and chipping and fading. The result is a finish that provides outstanding appearance over the exposure cycle.
*** Not Recommended for floors with Autos or Forklifts. The preferred product for that application is Epoxy Kote - 2-part epoxy. ***
SUGGESTED USES: Exterior, interior, concrete, steel, equipment, and anywhere a rugged industrial coating is needed
LIMITATIONS: Do not apply if material, substrate or ambient temperature is below 50°F or above 95°F.
COLORS: Available in over 30 factory packaged colors, as well as 1000 mixed colors.
VEHICLE TYPE: Epoxy Resin
SOLVENT TYPE: High Flash Naphtha VOC: 3.76 lbs. / gal (450 grams / liter)
SOLIDS BY WEIGHT: 50%<
WEIGHT PER GALLON: 10 lbs. per gallon (varies by color)
RECOMMENDED DRY FILM: 4.0 mils
COVERAGE: Theoretical coverage at two mils dry is 400 square feet per gallon, and recommended thickness of 4 mils dry would require 2 full coats. Material losses during mixing and application will vary and must be taken into consideration. Expect 50% less coverage on bare, rough or sandblasted surfaces.
VISCOSITY AT 75°F (24°C): 70-80 KU
AVERAGE DRY TIME 75°F: Dries to touch in 4 hours. Lower temperatures & higher humidity will slow down dry times.
RECOMMENDED REDUCER: Xylene for spray application, Hi Flash Naphtha for brushing or rolling
RESISTANCE TO: Chemical Resistance, Abrasion, Oils, Grease, Rust, Corrosion, Mildew, Chipping and Fading
RECOMMENDED PRIMERS: Jetcote Industrial Primers - 3038 Gray, 3037 Red, 3036 Black, 3039 Yellow
APPLICATION: Brush, Spray or Roller Roll: 1/2” nap mohair metal, lambskin, phenolic core roller. Keep roller wet. Roll in one direction, rewet, then cross roll. Product can be reduced as needed with Hi Flash Naphtha to allow proper flow out and performance.
Spray: Conventional Air Gravity Feed 59-70 psi, Tip Size .055 -.070, Airless 2200-2500 psi, Tip Size .013-.017. Product can be reduced with Xylene as needed for proper flow out and performance. For Air Spray reduce 25% with enamel reducer (Xylene.).
SURFACE PREPARATION: Water blast surface to remove all loose paint, dirt, oils and grease. Abrade with 240 grit dry sandpaper or equivalent. Solvent wipe down to remove all sanding residue. Prime with Jetcote Primer for best results.
POT LIFE: Not Applicable
SHELF LIFE: Maximum 12 months MIXING: Mechanically mix for 10 minutes, making sure that all solid material is mixed thoroughly.
PACKAGE: 1 Gallon cans, 5 gallon pails.
CLEANUP: Xylene for Equipment.
National Paint Waterbase Epoxy Tie-Kote is a two component water based epoxy tie-coat/sealer with excellent adhesive properties existing one and two part finishes. Primarily used on cleaned existing finishes which will be over coated with a two component solvent based finish which may attack the existing finish and cause a loss of adhesion. Can be used over chlorinated polymer pool paints, conventional solvent based and water based finishes such as alkyds, vinyls, acrylics and latex. Ideally applied by roller or brush but can be sprayed if desired.
Colors: Clear Amber
Vehicle Type: Amine Adduct Resin in Water
Solids By Volume: 47.0 +/- 1.0%
VOC Content: 0 grams/liter (reacted)
Weight per Gallon: 8.6 +/- 0.2 pounds
Recommended Dry Film Thickness: 2.0-2.5 mils
Coverage: Approximately 303 square feet per gallon at 2.5 mils DFT
Pot Life: 2-3 Hours
Shelf Life: 24 Months
Average Dry Time: Dries to touch in about 1 hour at 70-75 deg F. Can be top coated with solvent based epoxy finishes after an overnight cure.
Recommended Reducer: None recommended. Use tap water if necessary
Clean Up: Use tap water
Surface Preparation: Surface must always be clean, dry and properly prepared prior to painting. Failure to do so will lead to eventually blistering and/or peeling. High pressure fresh water clean if possible or solvent clean to remove all surface contaminants. Allow to thoroughly dry prior to over coating.
General Application: For use as a tie-coat/sealer over existing finishes that are desired to now be painted with solvent based epoxies. Apply by roller or brush. Add up to 10-15% by volume of tap water but only if necessary. Apply one or two coats if needed to meet dry film thickness requirements. Allow 15-20 minutes induction time after the curing agent component is added.
Mixing and Thinning: Shake or mix each component thoroughly. Add the curing agent component to the base component and stir thoroughly. Continue to stir while using.
Existing Painted Surfaces: First ensure the existing surface is compatible with a two component water based
PRODUCT DOWNLOADS:View full product details