ADDITIVES

1. Chips improve the appearance and texture of the surface.
2. May be use in light, medium or full dispersion to create a customized surface.
3. Chips improve slip resistance and safety.
4. Anyone can do it without special training.
5. Available in a wide variety of colors and sizes.

INTENDED USE: Shredded acrylic chips used to decorate and add non-slip texture to a liquid applied coating product.
SURFACES: Commercial, industrial or consumer floors.
SUBSTRATES: Wood, concrete, fiberglass, all metals and synthetic materials.
USES: Restaurants, retail spaces, commercial kitchens, basements, hospitals, laboratories, manufacturing areas, bathrooms and in retail venues. Widely used with epoxy garage floor coatings.
APPLICATION: Broadcast chips across the still wet surface of the base coat so they stick. Over coat with clear coating to seal and tie it all together.

1. Improves the viscosity and leveling properties of paint and coating products.
2. Use to clean up tools and spills.
3. Improves dry and cure times.

INTENDED USE: Use Leveling Thinner to thin and condition paint and coating products where recommended.
CLEAN UP: Use to clean up tools and spills.
RECOMMENDATIONS: Use with TS-100, TS-188, TS-200 & TS-780.

1. Improves the dry and cure times of concrete coatings.
2. Improves resistance to hot tire pick up.
3. Improves chemical resistance.
4. Concentrated pour in product.
5. Extremely effective.

INTENDED USE: A pour in additive for use with concrete floor coatings that accelerates and hardens concrete coatings and paint products.
RECOMMENDATIONS: Use with TS-100 Silicone Epoxy or TS-200 Mono-Epoxy. Acceptable for use on concrete, tile, masonry and wooden floor surfaces.

1. Improves dry and cure times.
2. Improves the viscosity and leveling properties of paint and coating products.
3. Enhances the penetration of paint and primer.
4. A strong and effective cleaning agent.

INTENDED USE: Use to thin and condition paint and coating products where recommended.
CLEAN UP: Use to clean up tools and spills.
RECOMMENDATIONS: Use with TS-66, TS-222, TS-664, TS-4985, TS-6390 & TS-6433.

1. Adds a slip resistant texture to paint and coating products.
2. Weightless in paint so it stays suspended better than heavier aggregate additives resulting in a more even finish.
3. Adds a decorative appearance where desired.

INTENDED USE: A non-slip additive for floor paint and coating products that produces a slip resistant surface.
SURFACES: Decks, floors, steps, patios, walkways, laundry rooms, kitchens, basements, pool decks, handrails, bathrooms.
APPLICATION INSTRUCTIONS: Pour contents of package into container of paint or coating and stir it in thoroughly.
NOTE: may lower the viscosity which may make thinning necessary.

1. Adds a slip resistant texture to paint and coating products.
2. Stays suspended better than silica aggregates resulting in a more even finish.
3. Adds a decorative appearance where desired.

INTENDED USE: An additive for urethane and epoxy floor coatings that adds texture and slip resistance.
SURFACES: Decks, floors, steps, patios, walkways, laundry rooms, kitchens, basements, pool decks, handrails, bathrooms.
APPLICATION INSTRUCTIONS: Pour contents of package into container of paint or coating and stir it in thoroughly.
NOTE: May lower the viscosity which may make thinning necessary.

1. Eliminates the need for grinding or blasting in many applications.
2. Neutralize with TSP.
3. Fast acting and highly effective.
4. Concentrate is cheaper to transport.
5. Corrects the pH.
6. Improves the bonding power of paint and coating products.

INTENDED USE: Use to remove contaminates, stains and grime from floors. An effective pre-paint cleaner-etcher solution.
SURFACES: Ferrous and nonferrous metals, fiberglass, concrete, tile, masonry and synthetic materials.
APPLICATION: Mix 1 part concentrate with 3 part water. Apply to pre-wet surface, agitate with a push broom as needed, allow to stand 20-30 minutes, flush thoroughly with water. Use undiluted to remove heavy contamination or for heavy-duty requirements.