|
The secret is out on TS-100 1 Part Epoxy. This easy
to use fully submersible waterproof roof coating replaces hard to
use multiple component epoxy and urethane in metal, tile, asphalt
and concrete roof paint applications. Its’ a one of a kind,
super-premium roof coating that is excellent for use on virtually
any roofing surface. A self priming single component epoxy roof
paint that that may be applied directly to tile, metal or concrete
without the need for primer saving you time, work and money! 1 Part
Epoxy is durable, environmentally friendly and non-toxic making it a
favorite of professional roofing contractors. 1 Part Epoxy Roof
Coating doesn’t need a primer and won’t chalk, fade or yellow, crack
or peel like two component epoxies. 1 Part Epoxy is a one of a
kind, super-premium protective coating that produces a film that
remains both hard and flexible at the same time. Its silicone
epoxy base allows high adhesion, flexibility, color fastness and UV
stability. Since its oxygen cured rather than catalyzed it holds its
color and gloss longer, is easier to work with and less hazardous.
No other product we are aware of has a wider range of application
possibilities. 1 Part Epoxy adheres to almost anything and it self
levels like a dream. Provides rust inhibiting protection and
excellent resistance to smog, grime, chemicals, alkali’s and acids.
It is impact resistant to 500 PSI and is heat resistant to 350+
degrees. If that weren’t enough it is a one coat application. One
coat covers up to three times the area of typical paint because its
maximum dry film thickness is only two mils. That’s half the
thickness of a sheet of paper! What more could you ask of any roof
coating. 1 Part Epoxy provides unequaled adhesion and performance on
steel, wood, ceramics, vinyl, aluminum, fiberglass, asphalt,
concrete and masonry surfaces. It is easy to use because it can be
brushed, rolled or sprayed and it cleans up easily.
Stats: Covers 400-450 square feet per gallon on porous surfaces such
as concrete, 600-800 square feet on non porous surfaces when
sprayed. Dry to the touch in 2-4 hours. Pot life: Not applicable *
Very high in solid content so it will require reduction in most
applications. May be applied direct to well prepared (etched) porous
surfaces. Compatible for electrostatic spray. Low temperature
curing (as low as 20 F.) Available in 200 stock roof paint colors.
Custom colors available on request for an additional $5.00 per
gallon.
Recommended preparation: For best results remove old roof paints,
loose scale, grease, oil and contaminates. Sand, grind, bead blast
or power-wash prior to the application of any cleaner or primer.
Steel: TS-5679 Phos-Pro Rust Converting
Cleaner, etch concrete, tile or asphalt materials with
TS-695 Etching Cleaner. All surfaces must be thoroughly dry
before the application of any roof coatings.
Recommended primers: Self priming on most porous surfaces. Glazed
tile and masonry-TS-6390 Ever-Last Epoxy
Primer or TS-664 Etching Primer.
Wood-TS-664 Etching Primer. Fiberglass, aluminum and composite
materials-best when used with TS 117
Pre-Wash Primer in combination with TS-664 Etching Primer.
Steel & iron: None.
Thin & clean up:
Use only with factory recommended thinner, TS-101 Thinner. Clean all equipment
thoroughly with TS-101 Thinner or TS-602
Mineral Spirits.
Accelerate/Harden: See
TS-160 Accelerator/Hardener on
SUPPLIES Page.
Acceptable uses: RV roof paint, tile roof paint,
aluminum roof coating, concrete roof paint, flat roof paint, metal
roof paint, RV roof coating, rubber roof coating, tile roof
paint, tin roof paint, waterproof coating, waterproof coating, steel
roof coating, steel roof paint. An alternative to: acrylic roof
paint, aluminum roof paint, concrete roof paint, elastomeric roof paints, epoxy roof paint, flat roof
paint, flat roof paints, rubber roof coating, zinc roof paint or
fiberglass roof paint.
Application Instructions
|
