Hard-Shell
Urethane is
a
two-component
catalyst
cured
aliphatic
urethane
formulated
for
professional
tub, tile,
sink and
countertop
refinishing.
What
separates
Hard-Shell
Urethane
from the
pack is that
it is a
permanent
refinishing
solution.
With
Hard-Shell
Urethane do
it once and
forget for a
lifetime! It
is a fully
submersible,
non-yellowing,
non-fading
colorfast
refinishing
system that
really
lasts. The
rock-hard
finish is
less likely
to scuff,
mar, change
colors,
loose its
gloss, crack
or peel.
Moreover, it
withstands
heat to 500F
making it
the right
choice in a
busy
commercial
kitchen.
Specifically
formulated
to out
perform all
liquid
refinishing
products.
Hard-Shell
Urethane is
resistance
to strong
cleaners,
chemicals,
heat, acids,
alkalis,
solvents,
minerals,
and
corrosion
over a
variety of
substrates.
Acceptable
for use on
bathtubs,
tile, sinks,
countertops,
shower
stalls, tub
surrounds
even hot
tubs! It
creates a
beautiful
colorfast
finish that
cannot be
burned,
stained or
discolored
by hot pots
and pans,
boiling
grease,
cigarettes
or household
cleaning
agents. With
proper
surface
preparation
and
application
it provides
the user
with years
of lasting
beauty and
protection.
Acceptable
for use on
almost any
surface.
Recommended
for use on
steel,
porcelain,
aluminum,
fiberglass,
laminates,
and wood.
May be used
with
Super-Fleck
Chips and
other
decorative
elements.
Available in
gloss,
semi-gloss
and satin.
Stats:
Covers
400-450
square feet
per gallon
depending on
surface and
specific
application
requirements.
Dry to the
touch in 30
minutes-1
hour. Mixing
Ratio: 7:1
(by volume)
with Part B
(Induction
Time: 15
minutes) Pot
life: 4
hours * It
is supplied
at spray
viscosity
suitable for
most
conventional
systems.
Compatible
for
electrostatic
spray. Low
temperature
curing (as
low as 20
F.)
Available in
one-half
gallon and
one gallon
kits.
Available in
low sheen,
semi-gloss
and gloss.
Recommended
preparation:
For best
results
remove old
aircraft
coatings,
loose scale,
grease, oil
and
contaminates.
Sand, grind,
blast or
power-wash
prior to the
application
of any
cleaner or
aircraft
primer.
Steel:
TS-5679 Phos-Pro
Rust
Converting
Cleaner,
etch
fiberglass
and aluminum
with
TS-695
Etching
Cleaner.
All surfaces
must be
thoroughly
dry before
the
application
of any
aircraft
paint
schemes.
Thin & clean
up: Use only
with factory
recommended
thinner,
TS-620
Thinner
Reducer.
Clean all
equipment
thoroughly
with
TS-620
Thinner
Reducer or
TS-610
Lacquer
Thinner.
NOTE:
Acceptable
uses:
aerospace
coating,
aircraft
coating,
aircraft
clear
coating,
high
performance
aircraft
coating. Use
with
aircraft
paint
schemes, aircraft paint and coatings,
aircraft
paint
colors,
high
performance
aircraft
coatings,
airplane
paints and
primers,
aircraft
paint and
coatings,
aircraft
paint
schemes,
aircraft
clear
coating and
high
performance
aircraft
coatings.
Application Instructions
