|
The secret is out on TS-100 1 Part Epoxy. This easy
to use protective coating replaces hard to use multiple component
epoxy and urethanes in industrial applications. Its’ a one of a
kind, super-premium industrial coating that is excellent for use on
machinery, tools, equipment and on industrial infrastructure. A
single component Direct To Metal coating (DTM) that is durable and
environmentally friendly. 1 Part Epoxy won’t chalk, fade or yellow
like two component epoxy and it is non-toxic when dry making it a
favorite in performance coating and rust preventative paint
applications. Now you can use our exclusive 1 Part Epoxy in your
direct to metal paint applications safely and economically without
the need* for primer in many instances. 1 Part Epoxy is a one of a
kind, super-premium protective coating that produces a film that
remains both hard and flexible at the same time. Its silicone
epoxy base allows high flexibility, heat resistance and UV stability
while providing the excellent hardness, scuff resistance and
chemical resistance you expect when you typically think of an epoxy
or urethane. Since its oxygen cured rather than catalyzed it holds
its color and gloss longer, is easier to work with and less
hazardous. No other product we are aware of has a wider range of
application possibilities. 1 Part Epoxy adheres to almost anything
and it self levels like a dream. Brush it on and watch the brush
marks disappear before your very eyes! Industry veterans recognize
this product as being something very special. A waterproof rust
inhibiting paint that offers excellent resistance to chemicals,
spilled fuel, brake fluid and acids. It is impact resistant to 500
PSI and is heat resistant to 350+ degrees. It is color-fast,
non-chalking and resists cracking, chipping and peeling.
Additionally, it covers up to three times the area of typical paint
because its maximum dry film thickness is only two mils. That’s half
the thickness of a sheet of paper! If that were not enough, it
typically covers in just one coat! What more could you ask of any
industrial paint? When used as a heat resistant coating, metal
coating, aluminum paint, pipe coating or tank coating it provides
exceptional performance and durability. 1 Part Epoxy provides
unequaled adhesion to Steel, Iron, Wood, Composites, Ceramics,
Vinyl, Aluminum, Fiberglass, Concrete and Masonry surfaces. It is
easy to use because it can be brushed, rolled or sprayed and it
cleans up easily. This lead-free formula is low VOC, is engineered
to provide extraordinary performance, durability, and is non-toxic
when dry so it is safe around children and animals.
Stats: Covers 400-450 square feet per gallon on porous surfaces such
as wood, up to 800 square feet on non porous surfaces. Dry to the
touch in 2-4 hours. Pot life: Not applicable * Very high in solid
content so it will require reduction in most applications.
Compatible for electrostatic spray. Low temperature curing (as low
as 20 F.) Available in low sheen, semi-gloss and gloss.
Recommended preparation: For best results remove old aircraft
coatings, loose scale, grease, oil and contaminates. Sand, grind,
blast or power-wash prior to the application of any cleaner or
aircraft primer. Steel: TS-5679 Phos-Pro
Rust Converting Cleaner, etch fiberglass and aluminum with
TS-695 Etching Cleaner. All surfaces must be thoroughly dry
before the application of any aircraft paint schemes.
Thin & clean up: Use only with factory recommended thinner,
TS-101 Thinner. Clean all equipment
thoroughly with TS-101 Thinner or TS-602
Mineral Spirits.
Accelerate/Harden: See TS-160
Accelerator/Hardener on SUPPLIES
Page.
NOTE: Acceptable uses: aerospace coating, aircraft coating,
aircraft clear coating, high performance aircraft coating. Use with
aircraft paint schemes, aircraft paint and coatings,
aircraft paint colors, high
performance aircraft coatings,
airplane paints and primers, aircraft paint and coatings, aircraft
paint schemes,
aircraft clear coating and high performance aircraft coatings.
Application Instructions
|
