Call us at 1-800-594-0445
Home
Shopping Cart
Color Charts
Find a Dealer
Find an Installer
Be a Dealer
Be a Distributor
Links
Who is Using TSC
Tech Info
Contact Us
About Us
Site Map
 


10

9317 State Street , Suite A, Marysville WA. 98270    Phone: 360-651-9050   Fax: 360-651-2540

 INSTRUCTIONS FOR APPLYING SUPER INDUSTRIAL FLOOR SYSTEM TO CONCRETE (1/3/06)

We have designed our Super Fleck Flooring System to be economical, easy to use and highly durable. We have prepared it in “kits” to provide you with enough product to cover a typical one car garage or about 250 square feet so if you have a two or three car garage you will require two or three kits accordingly.

It is best if concrete floors are allowed to cure 3or more months before application. Additionally, you DO NOT want to seal your concrete floor before applying paint because sealers are often incompatible with paint. Sealers can prevent paint from soaking into the concrete so it may not adhere if it has been sealed. You want to be certain your concrete surface has not been sealed before moving forward with your plans to paint. We recommend doing a small test area before you commit to the entire project. This could prevent major problems if there is a sealer you don’t know about or some unknown compatibility problem. Please be sure to test first!

1. Patch or repair any cracks, holes or divots with a compatible, porous patching material. Wash your surface with an acid wash solution. Follow the directions on the container. We recommend Rynolite cleaner as seen on our supplies web page. Concrete continues to leach lime even after cured so you have to deal with that before you paint. 

 

2. Before applying our paint you want to do a simple moisture test to be sure your concrete is dry enough to paint. Simply duct tape a small piece of preferably clear plastic to the floor and wait a few hours. If you see water droplets on the plastic the floor is too wet. Wait until the plastic shows no water droplets before proceeding.

 

3. Mix and apply the two-part epoxy primer coat according to the instructions on the can. It is best to roll this product on although you may want to brush the edges and corners. Allow to dry for 24 hrs.

 

4. Mix and apply the two-part urethane “color” coat according to the instructions on the cans. Allow to dry for 24 hrs.

 

5. Now its time to apply the two-part urethane clear coat. Mix and apply the clear coat according to the instructions on the cans. Allow to dry for 24 – 48 hours before walking on it. Allow 7-10 days for total cure to be achieved. Note: Do not over apply clear or it may take on an amber appearance.

 

We hope this information helps you achieve the results you want and that our product will give you years of problem free service. For more information please call us at 360-651-9050 M – F 9 AM to 6 PM PST or see us online at: www.topsecretcoatings.com

 

Warranties: Top Secret Coatings warrants satisfactory results when product is properly applied and used according to label directions, installation instructions and other literature.

 

The statements made on any of our literature, website or by any of our agents concerning our products, their potential applications or installation instructions are given for information purposes only. They are believed to be true and accurate and intended to provide a guide to approved construction practices and materials. As workmanship, product compatibility, weather conditions, application equipment, quality of other materials and other variables affecting results are beyond our control. Top Secret Coatings Inc. does not make nor does it authorize any agent or representative to make any warranty of MERCHANTABILITY OR fitness for any purpose or any other warranty, guaranty or representation, expressed or implied.

 

Top Secret Coatings warrants that its goods, as described on the face hereof, are free from any defects in material or workmanship. Seller makes no other warrantee, express or implied, and all implied warranties of merchantability and fitness for a particular purpose are hereby disclaimed. Seller shall not be liable for prospective profits or special indirect or consequential damages. Seller’s sole liability and buyer’s exclusive remedy for breach of any warranty as expressly limited, at seller’s option, to replacement at the original F.O.B. point or refund of purchase price.  Seller shall not be responsible for any claim resulting from failure to utilize product in the manner in which it was intended and in accordance with instruction provided for use of product. Any claim for breach of warranty shall be deemed waived unless buyer shall give seller written notice of such claim within thirty (30) days after delivery and shall allow seller reasonable opportunity to investigate claim and inspect product.